Follow

Registering your Device with Endian Network (Part 3 of 3)

Version 2.5 Version 3.0

Applies to Platform: UTM 2.4, UTM 2.5; 4i Edge 2.5
Last Updated: 27 May 2014

Applies to Platform: UTM 3.0, 4i Edge 3.0
Last Updated: 27 May 2014

This lesson will illustrate the steps necessary to register your device with Endian Network. This will be required after the initial configuration and network settings are configured.

Warning

Your Endian device must be connected to the Internet in order to successfully register. Do not attempt to register until you've confirmed a successful Internet connection.

Background Information

?name=media_1303139426699.png register.png

After you complete Part 1 and 2 of the device and network configuration, you will be prompted to register your device to Endian Network.

If you have never registered a device or created an account with Endian Network--> Proceed to Step 1

If you have registered a device before or created an account with Endian Network --> Skip to Step 4

 

Note

Registering your device will allow you to receive updates and upgrades, remote support, and activate your license offficially with Endian so this is highly recommended you do this immediately!

Step 1 - Create Endian Network Account

?name=media_1303143987166.png register1.png

Select No and hit Forward (fwbutton25.pngfwbutton.png). You will then be taken to the next screen which will provide a link to the Endian Network account creation page. You can click the link in the Endian interface or click below to begin the registration process.

https://network.endian.com/register.php

Step 2 - Verify Activation Code

?name=media_1303144394785.png register2.png

You will need to verify your activation code before being allowed to create your account. Please provide the 12-character alphanumeric code formatted as above (XXXX-XXXX-XXXX).

Click on Continue to proceed.

Step 3 - Complete Account Form

media_1303144673657.png register3.png

Next complete the short form to finalize your account creation. Be sure you make a special note of your login and password as you'll need this to register all future Endian devices.

Click on Create account to finish.

Step 4 - Register Endian Device

?name=media_1303150647231.png register1.png

Now back on the Endian device, you can select the Forward button to continue and register your device.

Continued from Background Info...
If you have already created an account --> Then select Yes when asked whether you already have an Endian Network account and hit continue Forward.

Step 5 - Complete Device Registration

?name=media_1303151075336.png register4.png

The last step is to complete the device registration form with your Endian network username (login) and password and device activation code. The "System Name" field is just a generic descriptive string used to identify the device within Endian Network.

Click Register when the form is complete to finish the registration process.

Verify Registration

?name=media_1303151272139.png register5.png

Once your device complete the registration, you should see a confirmation screen similar to the above.

You can click Finish to proceed to the main web interface of the device.

Was this article helpful?
1 out of 1 found this helpful
Have more questions? Submit a request

Comments

  • Avatar
    Daniele De Lorenzi

    Still valid for 2.5

  • Avatar
    Luca Radaelli

    I would add to check if network.endian.com is resolved correctly by DNS.

    To do this login via ssh on Endian UTM Applicance and run

    ping network.endian.com

    If an error is show check your dns configuration.

  • Avatar
    Frank Korpershoek

    The dns check is very usefull. The error you get in the webinterface isn't : 'error in enclient' In addition, I'm not sure, but I think the correct time is important too. After I resolved this dns problem, I was still not able to register, but after a ntpd restart the registration succeeded. Please make the webinterface error more descriptive.